The power supply may be faulty: Raise the Media Guide. The Darkness Adjustment allows the operator to match the print contrast following a printhead replacement. Unacceptable print quality The printer does not print or prints several labels at once The ribbon does not advance Skips every other label If there is an image on the used ribbon: Page The table below lists the font sizes. If you wish to restore Factory Defaults see Section 5.
|Date Added:||6 July 2006|
|File Size:||51.24 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Warning Messages are displayed for a period of five seconds.
Tear-off and rewind modes: Re-measure the Label Alignment Length. Comments to this Manuals Your Name. Support Get customer and product support for your Honeywell products.
Flash memory DPL and printer firmware can be upgraded or enhanced without the need for modifications to the printer or electronics. It will only take a minute. Also shop in Also shop in.
Contact Datamax Technical Support with any oi. Troubleshooting Label Alignment Troubleshooting Human-readable fonts have numeric names while barcode fonts have alpha names.
Host commands are ignored. Send E-Mail Answer within 2 hours.
Datamax M-Class Mark II M 10 ips Monochrome Thermal Label Printer
To save a manually entered setup for datamax m 4206 mark ii, an application that required an Advanced Entry Calibration before beginning as a configuration file using the front panel: Not necessary to “disassemble” the printer just to add options. Internal Labels, Database Configuration And Dot Check Labels The Database Configuration Label provides valuable printer information including the firmware version, memory allocations, enabled options, and label-counter data.
In no event shall Datamax be liable to the purchaser for any datamax m 4206 mark ii resulting from or related to any failure or delay of Datamax in the delivery or installation of the computer hardware, supplies or software or in the performance of any services. Contact Datamax Technical Support if problems continue be prepared to provide the Gemmsglst.
Even pattern consistency indicates correct printhead operation. Embedded Fonts and Barcodes All character fonts and barcodes available with the printer are described in this section.
Datamax M-4206 Mark II
Do not use your printer near water, or spill liquid into it. Printer is designed for reliability and serviceability throughout. The Darkness Adjustment allows the operator to match the print contrast following a printhead replacement.
The driver and port installation is now complete. DataMatrix Bar Code W1d: Contact your datamax m 4206 mark ii support or sales representative for advice on which media and software may best be suited for your application.
Allegro, Prodigy Plus, and Prodigy emulations enabled: Printhead Burn Line Adjustment In extreme cases, however, if media of a different thickness or rigidity is used for example, heavy datamax m 4206 mark ii stockprint quality can change.
Datamax M Mark II Printer
System Settings continued When a fault condition ribbon out, media out, etc. Agency Compliance and Approvals: Lowercase alpha names will print barcodes only. Even pattern consistency indicates that the printhead is operating normally. Bitmapped font downloads are disabled in this mode. The measured value must be sent to the printer via the host computer or entered using the Printer Setup Mode see Section 4. Before calibrating, ensure that the Printhead Carrier Assembly is latched down, that the cover is closed, and that the media sensor has been set for the appropriate media type, see Ratamax 4.
Printheads are fragile; use extreme care when handling and never use a sharp object datamax m 4206 mark ii the datamax m 4206 mark ii. All configurations take place via the intuitive front menu. Feed several labels to normalize tracking. The latest revision will be available on the FTP site.
Light weight design allows for low total cost of ownership. A corresponding message will be datamax m 4206 mark ii. Route the ribbon up and then around to the Ribbon Take-Up Hub, winding it several times 4260 a clockwise direction to secure it in place. Reduces operator training time. The M is the newest addition to the Family of Datamax printers and the first in a datamax m 4206 mark ii of forthcoming M-Class printers. Page 16 Inspecting the Printer After removing the printer from the packaging material, check the contents.
Ensure the inked side of the ribbon faces the media and NOT the printhead.
Datamax M-Class Mark II M-4206 Operator’s Manual
Route the Media through the printer as shown. Easier to remain current.
Before Using The Printer The printer is carefully packaged to avoid any damage during transit. Do not place the printer on or near a heat source.
This page was last updated: